|
1) MANUFACTURING RANGE
| |
dimension
series |
d |
Cage |
single
row -
standard |
618,
619, 160, 60, 62, 622, 63, 64 |
17...180
mm |
M,MA,MB |
single
row -
specials |
650,
651, 652, 653, 654, 655, 656, 657, 658, 659, 660, 885,
MR |
17...390
mm |
M,MA,MB |
double
row -
standard |
42 |
25
mm |
|
| single
row - with increase load |
BL62,
BL63 |
35...90
mm |
|
| single
row - magneto type |
E |
20
mm |
|
| single
row-with extended inner ring |
UCC2,
UCC3, USC2, UEC2, FHSR2 |
17...65
mm |
|
| single
row-with extended inner ring and spherical outer ring |
UC2,
UC3, US2, UE2, UK2, FHS2, FH2, FHR2, UC5 |
17...65
mm |
|
| single
row-with spherical outer ring |
UD2 |
25...45
mm |
|
| Water
pump bearings |
P16,
P20, PR20, 8851, 8857, 8858 |
15.918..20
mm
D= 30...47
mm |
TN |
| double
row-specials |
RT,
RTS, RTZ |
7.5..15.920
mm |
TN |
| pressure
cylinder bearings for textile machines |
LP101,
LP132, LP302, LP314, LP315, LP316, LP317, LP701 |
68.4...150
mm |
TN |
2) DESIGN TYPES -
open; UG; RSR (one seal); 2RSR (two seals); ZR (one shield);
2ZR (two shields);N, NR standardized and unstandardized as
well.
3) TECHNICAL EXECUTION CONDITIONS
a) DIMENSIONS The
boundary dimensions according to ISO 15.
b)
TOLERANCE CLASSES
P0, P6 and P5 according to ISO 492, ISO 199.
c)
RADIAL CLERANCE
C2, normal C3 and C4 according to ISO 5753.
d)
The basic load ratings are established
in accordance with ISO 76 and ISO 281.
4) CAGE TYPES -
Pressed steel cage. - Moulded snap type cage of glass fibre
reinforced polyamide (suffix TN).
5) APPLICATIONS
a)
ENGINEERING MACHINE INDUSTRY
-
Gear boxes and reductors. - Grinding machine. - Compressors.
- Fans. - Pumps.
b)
TRANSPORT INDUSTRY
-
For road vehicle units ( gear box, water pumps) - For railway
vehicles (reductors).
c)
PAPER AND CELLULOSE INDUSTRY
-
Rolls - Calenders
d)
CHEMICAL INDUSTRY
e)
ENERGETICS INDUSTRY -
Electrical engines.
6) SUGGESTIONS
a)
MISALIGNMENT
Tilting values of the bearing rings may vary from 2 to 10
minutes of arc in regard to the radial clearance, and the
size of the loads. We point out that during running the ring
misalignment couses noise.
b)
MINIMUM RADIAL LOAD
That one can be calculated approximately with the formula:
Fr min =0,01*Cr and there are taken steps to achieve it, when
the force is not provided by the mass of the bearing components
and of the external forces.
c)
AXIAL LOAD
For axial loads bigger than 0,25*Cor, please, ask for the
specialists advise.
d)
RUNNING TEMPERATURES
Series made bearings can be used at temperatures of -30 through
+110 0C. The special greases allow utilisations at temperatures
of -50 through +120 0C.
|
